Prove 2 is a digital smart card simulator designed to assist you in developing terminals, contactless frontends (CLFs) and chip stacks.
It covers all interfaces of the UICC: ISO/IEC 7816, SWP/HCI, and IC-USB.
With its ability to perform the same digital test cases used by UT³ Platform for device certification at GCF and PTCRB, Prove 2 is your tool for pre-conformance testing. Additionally, it is a cost-effective solution for regression testing of mobile phones.
Together with COMPRION’s CLT One, a synchronized simulation of contact-based and contactless communication allows comprehensive CLF testingof NFC-enabled phones and devices. The complete communication between terminal and smart card can be conveniently monitored and easily analyzed by help of translators. In addition, the integrated digital storage oscilloscope allows signal analysis even on the electrical level. COMPRION’s user friendly Device Test Center software provides
access to all functionalities of Prove 2
Prove 2 enables terminal testing on all interfaces: ISO/IEC 7816, SWP/HCI, IC-USB.
Main use cases are
GCF/PTCRB pre-conformance testing
— CAT/SWP/HCI
— USIM/USAT
GSMA TS.27 NFC Handset Test Book
— BIP
— General Device Support
— Remote Management
Development/debugging of
— Mobile phones
— Chipsets
— M2M devices
Combined NFC/SWP/HCI testing
Quality assurance
GCF/PTCRB pre-conformance platform
Combined synchronized testing of contact-based
and contactless interfaces (with CLT One)
Automated handset testing in combination
with network simulators (COMPRION SIMfony)
Powerful card simulation
Integrated oscilloscope
Communication tracing on all UICC contacts
(ISO/IEC 7816, SWP/HCI, IC-USB)
Powerful analyzers for timing measurements
and error identification
Capabilities
CLF and Terminal Testing/Smart Card Simulation
According to ETSI TS 102 613 (SWP),
ETSI TS 102 622 (HCI),
3GPP TS 31.102 (USIM), and
ETSI TS 102 600 (IC-USB)
Logical protocol parameters adjustable
Error simulation
S1/S2-signal at C6 contact:
— Adjustable current value for S2
— Measurement of voltage (S1) and current (S2)
Advanced SWP test features
— Extended bit duration
— Support of selective reject s-frame (SREJ)
Basic ISO/IEC 7816 T=0 simulation and
basic SIM/USIM application simulation
IC-USB: ICCD simulation
ISO/IEC 7816 Monitoring
Structured view of the terminal profile
Timing information for each entry
Translation of Remote File Management commands
Supported ISO/IEC 7816 protocols: T=0, T=1
SWP/HCI Monitoring
Based on ETSI TS 102 613/ETSI TS 102 622
Based on proprietary SWP standard Inside
Contactless
SHDLC (Simplified High Level Data Link Control)
Contactless tunneling (CLT)
IC-USB Monitoring
Based on ETSI TS 102 600
Advanced EEM interpretation
Mass storage: SCSI command interpretation
Monitor of bytes/frames/bus-states
General Monitoring Features
Display and analysis of communication
— During test case execution
— Between terminal and smart card*
— On physical, protocol, transport and application layer
Universal Translator
Supporting GSM, W-CDMA, LTE and CDMA2000
(incl. SIM/SAT, USIM/USAT, CSIM/CCAT, ISIM)
NFC Synchronzation Package
COMPRION SyncBus enables the
synchronization with NFC testing devices
CLT Move or CLT One
External I/O
Interface for external I/O signals
COMPRION MoVie
Stand-alone viewing software for logfiles traced
with COMPRION test tools
Analog Scope/Analog Scope Viewer
Integrated digital storage oscilloscope
Quick measurements
— Fall/rise times
— Peak-to-peak
— Top/bottom
— Duty cycles
Max. number of channels: 16 digital, 2 analog
Analog voltage measurements (res. ~1.8 mV)
on contacts VCC, RST, CLK, I/O and SWP
Analog current measurements on contacts VCC and SWP
Test Suites
SWP/HCI Test Benches
Prove 2 ETSI TS 102 694-1 SWP
Prove 2 ETSI TS 102 695-1 HCI
Prove 2 ETSI TS 102 695-3 HCI
Prove 2 ETSI TS 102 384 CAT SWP HCI
ISO/IEC 7816 Test Benches
Prove 2 ETSI TS 102 230 UICC
Prove 2 3GPP TS 31.121 USIM
Prove 2 3GPP TS 31.124 USAT
IC-USB Test Benches
Prove 2 ETSI TS 102 922-1 IC-USB
GSMA TS.27 NFC Handset Test Book
Prove 2 GSMA TS.27 General Device Support
Prove 2 GSMA TS.27 BIP
Prove 2 GSMA TS.27 Remote Management
GlobalPlatform Test Bench
Prove 2 GlobalPlatform SEAC Device Test
SIMalliance Test Bench
Prove 2 SIMalliance OMAPI
General Features
Supported smart card voltage:
1.2 V / 1.8 V / 3 V / 5 V
Supported IC-USB modes:
ICCD, ethernet emulation module, mass storage
Supported technologies: GSM, W-CDMA, LTE,
CDMA2000 and TD-SCDMA
COMPRION Monitoring Remote Control
COMPRION Remote Simulation Server
Time-synchronization interfaces
— High-speed COMPRION SyncBus
— Trigger out: Connection between
Analog Scope and external oscilloscope
(1 V signal level at 50 Ω)
Firmware updated automatically
via USB interface
Scope of Delivery
Prove 2
Device Test Center
Flex adaptor types A-D (terminal connectors)
Plug-in SIM adaptor (PISA)
USB cable
AC power plug (100–240 V / 50–60 Hz, ±10 %)
for DC power supply (12 V, 2 A)
Host Requirements*
Processor operating frequency: min. 2 GHz
(2 x 1.5 GHz dual core or more recommended)
RAM: min. 4 GB (8 GB recommended)
Hard disc (available space): min. 10 GB
USB interface: min. USB 2.0 highspeed
Supported OS: Windows 7, 8.1 and 10
* Host is not part of the delivery
Dimensions
W x D x H: 180 x 180 x 48 mm
Weight: 2.2 kg